IMPORTANT PRECAUTIONS

ITC Spa, Inc. strongly suggests that you contact your local, qualified electrician and plumber to install your Footspa. It cannot operate efficiently or safely unless it is provided with adequate electrical power, sufficient water pressure, proper water temperature and required drain facilities. Information on these important subjects is contained in this manual. We urge you to read it carefully to make sure these requirements are met.

PRECAUTIONS

1.       Excessive water temperature is dangerous and should be checked BEFORE use. Maximum temperature of water should never exceed 100 degrees F.

2.       Always enter and exit the Footspa slowly and carefully.

TELL EACH AND EVERY CUSTOMER TO "SLOW DOWN"

3.       NEVER bring and/or operate any chemical devices into or near the Footspa.

RECEIPT & INSPECTION

PLEASE TAKE NOTE! Thoroughly inspect each shipment immediately upon arrival. It is important that you notify the driver and insist on a notation of the damage. Make this notation directly on the face of the freight bill or bill lading. Failure to note damage on the face of the freight bill or bill lading may impede and/or prevent any claims that you may have against the carrier.

If concealed loss or damage is found, you must notify the carrier at once and request an inspection. DO NOT DISCARD THE SHIPPING CARTON. If you give the carrier a clear receipt for goods that have been damaged in transit, you do so at your own risk and expense.

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

ULTILITIES

ITC Spa must be conveniently located near adequate utilities; such as:

A - ELECTRICAL SERVICE

An 110V, 60Hz, 15Amp, GFCI protected grounded circuit MUST be used to supply power to the Footspa. A dedicated circuit must be used with a GFCI. All wiring must conform to National and Local Electrical Codes.

B - WATER SUPPLY

Water supply to the pedicure spa should consist of a system that will provide both adequate water pressure and water temperature. All plumbing connections must conform to local codes.

B.1 - WATER PRESSURE

Normal water pressure of 30 to 120 PSI is required to correctly fill the tub to proper levels.

B.2 - WATER TEMPERATURE

The water temperature should never exceed 100 degrees F. This temperature should not pose a problem for any normal water heater in good working order.

C - DRAIN FACILITIES

Connect the Footspa drain to meet local plumbing codes using 1-½ schedule 40 PVC drain pipe and appropriate traps (refer to detailed Installation Drawings in this manual).

CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL

The installation MUST comply with local, state and national building, plumbing and electrical codes, where applicable. A licensed plumber should complete the installation. Electrical wiring, components and connections MUST be completed by a licensed electrician.

A - LOCATION AND SUPPORT CONSIDERATIONS

Select a level location where the floor structure beneath the Footspa is capable of supporting the Footspa.

B - PLUMBING CONNECTIONS

All plumbing connections, drain and fresh water should be made by a qualified, licensed plumber in accordance with local plumbing and building codes.

B.1 - HOT AND COLD WATER SUPPLT LINES

Carefully connect ½" ID supply tubes to a fresh water source. Shut-off valves should be utilized.

B.2 - CONNECT DRAIN

Using 1-½ schedule 40 PVC drain pipe and appropriate traps, connect drain to meet local plumbing codes. Refer to Installation Drawing in this manual for options.

C - ELECTRICAL CONNECTIONS & WIRING INSTRUCTIONS

All electrical connections MUST be made by a qualified, licensed electrician in accordance with Local and National Electrical and Building Codes. An 110V, 60Hz, 15Amp, GFCI protected grounded circuit MUST be used to supply power to the Footspa (220V if ordered). A dedicated circuit must be used with a GFCI. All wiring must conform to National and Local Electrical Codes.

WIRING INTRUCTIONS:

1.       Remove outlet cover.

2.       Supply power: An 110V, 60Hz, 15Amp, GFCI protected grounded circuit must be used. (220V if ordered)

3.       Using appropriate connector, tie together black (Hot) wires. Using another connector, tie together white (Neutral) wires. Using a third connector, tie together green (grounding) wires.

4.       Replace duplex outlets and cover.

5.       Plug pump/motor into once outlet. Plug AC adapter/transformers into outlets. Plug control box for seat motors into outlet.

D - TESTING THE FOORSPA

After the plumbing and electrical connections have been made and the base unit has been secured to the floor, clean the tub and fill with water to above the 4 Jets escutcheon cover level.

After the tub is filled with water, press the button on the front of the Footspa and check for leaks at the drain overflow and all inlet and suction fittings. After checking under the tub for leaks, press the same button a second time to turn the pump motor "OFF" and drain the tub of water.

TO FILL: Close the over-flow/waste control. Utilizing the single level faucet located on the front of the Footspa, fill the tub with water. You must completely submerge 4 jets. If, during operation of the whirlpool, water level decreases, simply add more water.

TO START: Press button on the front of Footspa. Press again to shut off pump.

SEAT & BACK ADJUSTMENTS

Both seat bottom and seat back are adjustable. Simply press the appropriate button on the hand held control wand to change the position

CLEANING THE FOOTSPA:

Keep the lint screen on the suction inlet clean. Any blockage or obstructions in the screen reduces the whirlpool action and may cause damage to the pump. It is not necessary to remove the screen to clean it, however it may be removed. To clean the screen, unscrew the fitting cover. Remove any lint or debris and then wash the screen with a soft brush. Replace the screen.

CLEANING THE ACRYLIC SURFACES:

Your Footspa will be a continual delight over the years if you merely give it ordinary care. The Footspa is manufactured using the highest quality materials. DO NOT USE ABRASIVE PADS OR CLEANERS THAT WILL SCRATCH OR DULL THE PLASTIC SURFACE OR THE METAL ACCESSORIES.

After the Footspa is cleaned with a non-abrasive cleanser and thoroughly dried, a light coat of a qualified, clear liquid wax (example: Future™) may be used to maintain a "like new" finish. However, this wax must be used very sparingly, especially in the tub area itself.

The chrome plumbing fixture and fittings have a baked-on coating which should be cleaned ONLY with gentle soap, warm water and dab dry with a clean, soft cloth.

CLEANING/FLUSHING THE WHIRLPOOL SYSTEM:

It is recommended that the whirlpool system (includes pump, jets, suction fitting, piping, etc.) be flushed periodically (Not exceed 30 days). This is over and above the normal cleaning of the exterior plastic surfaces. The interior of this system may be flushed as follows:

1.       Fill Footspa with hot water to required level.

2.       Add 3 teaspoons of a low foaming dishwasher detergent such as Calgonite or Cascade, and 2 ounces of household bleach, such as Chlorox, to the water.

3.       Run whirlpool for 10-15 minutes and drain Footspa.

4.       Fill with cold water to required level and run unit for another 5-10 minutes. Drain Footspa, and wipe dry with a soft cloth.

NOTE: Whirlpool action can cause even a small amount of soap or body oil to foam excessively. For this reason, refrain from using these products during the whirlpool cycle.

The use of the Pedicure Spa and/or Chair Massage may be hazardous to your health.

If you have medical condition which you think may cause you sickness, please inform the Management, or the Manager.

The use of the Pedicure Spa and/or Chair Massage is voluntary and Customer agrees to release Management, its Owner, and the Store of any and all liabilities arising out of the use of these services.

Thank you.

The Management

ONE YEAR FIBERGLASS SHELL/ONE YEAR PLASTIC SHELL STRUCTURAL WARRANTY:

The spa shell is warranted to be free from defects in material and workmanship under normal use and maintenance for period of one (1) year from date of original purchase. ITC SPA, Inc. will repair or replace the shell at its sole option. As long as the spa shell holds water, the terms of warranty period only the remaining time under this warranty. The shell is further limited to be structurally sound; meaning capable of holding water only. The shell is further limited to 100% coverage for the first year and 10% reduction of the coverage of the replacement price by ITC SPA, Inc. each month following the first month, until one year of warranty is completed. The spa shell is warranted to the original purchaser only. The spa shell is defined as the shell below the acrylic finish. Any cost incurred for diagnosis of defects and/or failure or for labor in the removal and/or reinstallation of the spa shell is not provided for under the term of this warranty and shall be the responsibility of purchaser.

ONE YEAR MASSAGE MACHINE AND LABOR WARRANTY:

This product is fully guaranteed to the original purchaser against defects in material and/or workmanship under normal use and maintenance for period of one (1) year, and 30 days on labor, from the date of original purchase, provided the equipment has been operated according to the instructions accompanying it. This warranty is not valid if the product has been misused or damaged in any way that is beyond our control. This warranty applies only to the product and we are not responsible in any way for loses, damage or inconvenience caused by equipment failure.

30 DAYS PLUMBING WARRANTY:

ITC SPA, Inc. warrants all plumbing components to be free from defects in material and//or workmanship for period of 30 days on parts and labor from the date of purchase.

ONE YEAR PIPELESS JET MOTOR AND LABOR WARRANTY:

Pump manufacturer warrants water pump to be free from defects in material and workmanship for a period of one (1) year from the date of purchase, except as noted below. Pump which becomes defective within the warranty period will be repaired or replaced excepted for damage related to water chemistry, negligence, abuse, misuse, misapplication, unauthorized, modifications, improper installation, normal wear and tear or chemical attack. This warranty extends only to original purchase. Pump seals, pump motors. O-rings and gaskets are covered only during the first year of the warranty period, and 30 days on labor, from the date of purchase.

ONE YEAR DRAIN PUMP LIMITED WARRANTY:

Little Giant Pump manufacture Co. warrants pump to be free from defects in material and workmanship under normal use for one (1) year from the date of purchase. Refer to Little Giant Pump Company operating instruction manual.

ATTENTION: We only charge $50 for the time and transportation of technician to fix the product under one (1) year warranty period. (Only customer within 60 miles from Ontario, CA)

PERFORMANCE

In the event of a defect covered under the terms of this Limited Warranty, notify your ITC SPA dealer or manufacture. Use all reasonable means to protect the pedicure spa from further damage. Manufacturer or its representative will repair the pedicure spa subject to the terms and conditions contained in this Limited Warranty. Reasonable travel or trip charges may be assessed by manufacturer or its representative in situations where the pedicure spa is located outside the nearest service agent's normal service area. If manufacturer determines that repairs are not feasible due to a functional defect, we reserve the right to provide a replacement pedicure spa in lieu of repair. In such event, the costs for removal of defective pedicure spa and delivery and installation of the replacement pedicure spa will be responsibility of the pedicure spa owner. Manufacturer reserves the right to an on-site inspection by its authorized service representative.

EXCLUSIONS

This Limited Warranty is void if the manufacturer has been subjected to alteration, neglect, misuse, or abuse; if any repairs have been attempted by anyone other than manufacturer authorized service representative; or if failure is caused by the accident by anyone other than manufacturer authorized service manufacturer. Alterations include plumbing changes, electrical conversions, or additions of alternations sanitation which contribute to component failure. Neglect, misuse, abuse include any installation, operation or maintenance of the pedicure spa other than in accordance with the Owner's Manual or use for which the pedicure spa is not designed. Specifically, damage caused by dirty, damage to the pedicure spa surface caused by improper use of chemicals, allowing undissolved spa sanitizing chemicals to lie on the surface, damage to the pedicure spa surface caused by leaving sufficient to support the pedicure spa (according to standard building practices), are considered abuses and may invalidate this Limited Warranty.

DISCLAIMERS

Manufacturer or any of its authorized agents shall not be responsible for any costs incurred to provide access to any part of the pedicure spa for service. Foot Spas being surrounded with building materials should be water tested and operated prior to installation. Manufacturer or any of its authorized agents shall not be held liable for injury, or loss of use of your pedicure spa or any other incidental or consequential costs, expenses or damages, which may include but are not limited to the removal of other custom fixtures. In no event shall manufacturer be liable, for any reason or cause, in excess of the amount paid for the product. No other warranties, expressed or implied are valid. No agent, distributor, dealer, service company or other party is authorized to change, modify, or extent the terms of this Limited Warranty in any manner whatsoever. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.